Search found 14 matches
- Thu Dec 03, 2015 7:32 pm
- Forum: EMU STANDALONE
- Topic: 2jz knock sensors
- Replies: 9
- Views: 3529
Re: 2jz knock sensors
my setup 2jz-gte
- Fri Nov 14, 2014 10:25 am
- Forum: EMU STANDALONE
- Topic: Trigger settings for 1JZ with 12 tooth trigger wheel
- Replies: 15
- Views: 10426
Re: Trigger settings for 1JZ with 12 tooth trigger wheel
my settings 2jz
use Cam sensor #2
use Cam sensor #2
- Sun Sep 21, 2014 12:27 pm
- Forum: EMU STANDALONE
- Topic: Cam sync trigger tooth error 2jzgte
- Replies: 16
- Views: 7473
Re: Cam sync trigger tooth error 2jzgte
The problem is solved.
Set sensitivity switch for 500 RPM.
Correct primary trigger angle for 37.
Correct ignition map.
Correct idle map.
Engine running very good!
Thank you all
Set sensitivity switch for 500 RPM.
Correct primary trigger angle for 37.
Correct ignition map.
Correct idle map.
Engine running very good!
Thank you all
- Sat Sep 20, 2014 7:52 pm
- Forum: EMU STANDALONE
- Topic: Cam sync trigger tooth error 2jzgte
- Replies: 16
- Views: 7473
Re: Cam sync trigger tooth error 2jzgte
tried, ignition ok, but no idle...
- Fri Sep 19, 2014 4:43 pm
- Forum: EMU STANDALONE
- Topic: Cam sync trigger tooth error 2jzgte
- Replies: 16
- Views: 7473
Re: Cam sync trigger tooth error 2jzgte
wiring connect correctly...
if sensitvity switch RPM is ON 2000rpm - engine running good, but in the transition 2000 Rev. failure, above 2000 - all is good...
if sensitvity switch RPM is ON 2000rpm - engine running good, but in the transition 2000 Rev. failure, above 2000 - all is good...
- Wed Sep 17, 2014 9:11 pm
- Forum: EMU STANDALONE
- Topic: Cam sync trigger tooth error 2jzgte
- Replies: 16
- Views: 7473
- Wed Sep 17, 2014 8:43 pm
- Forum: EMU STANDALONE
- Topic: Cam sync trigger tooth error 2jzgte
- Replies: 16
- Views: 7473
Re: Cam sync trigger tooth error 2jzgte
2k and higher
- Wed Sep 17, 2014 8:35 pm
- Forum: EMU STANDALONE
- Topic: Cam sync trigger tooth error 2jzgte
- Replies: 16
- Views: 7473
Re: Cam sync trigger tooth error 2jzgte
Ok
change trigger edge from rising to falling - became even bad
shields of crank and cam sensors - check tomorrow
change trigger edge from rising to falling - became even bad
shields of crank and cam sensors - check tomorrow
- Wed Sep 17, 2014 8:21 pm
- Forum: EMU STANDALONE
- Topic: Cam sync trigger tooth error 2jzgte
- Replies: 16
- Views: 7473
Re: Cam sync trigger tooth error 2jzgte
Tried 10k-20k-30k, does not help...
- Wed Sep 17, 2014 7:56 pm
- Forum: EMU STANDALONE
- Topic: Cam sync trigger tooth error 2jzgte
- Replies: 16
- Views: 7473
Re: Cam sync trigger tooth error 2jzgte
where to connect a resistor?
- Wed Sep 17, 2014 5:17 pm
- Forum: EMU STANDALONE
- Topic: Cam sync trigger tooth error 2jzgte
- Replies: 16
- Views: 7473
Cam sync trigger tooth error 2jzgte
Hello!
My problem - if rpm above 2000 - begin cam sync trigger tooth error and dwell error...
My problem - if rpm above 2000 - begin cam sync trigger tooth error and dwell error...
- Wed Aug 20, 2014 4:19 pm
- Forum: EMU STANDALONE
- Topic: idle valve 2JZ-GTE
- Replies: 5
- Views: 6069
Re: idle valve 2JZ-GTE
Ok, thanks!
Now outputs - "not assignet" and stepper not working...
Now outputs - "not assignet" and stepper not working...
- Wed Aug 20, 2014 3:43 pm
- Forum: EMU STANDALONE
- Topic: idle valve 2JZ-GTE
- Replies: 5
- Views: 6069
Re: idle valve 2JZ-GTE
Idle-Parametrs-unipolar stepper - not active...
- Tue Aug 19, 2014 11:58 pm
- Forum: EMU STANDALONE
- Topic: idle valve 2JZ-GTE
- Replies: 5
- Views: 6069
idle valve 2JZ-GTE
Hello!
How to connect and configure the idle valve on the engine Toyota 2JZ-GTE?
How to connect and configure the idle valve on the engine Toyota 2JZ-GTE?