Ecumaster forum

hi!tell me what module to buy? and whether there is at whom the scheme of connection to emu...

Sports management system ECUMASTER EMU Two map 1-city of 250-300 km , 2-fight 400+. The transition from one card to another is carried out without resetting the gas switch. - Launch Control! Installed a start. - Flat Foot Shifting! Shifting gears without releasing gas. - Intercooler size 550/240/60-...

https://scontent.fhen2-1.fna.fbcdn.net/v/t31.0-8/21083001_1409097265870114_1883282686399372079_o.jpg?oh=e4545570982e4884f3e72e2f5038dc1a&oe=5A5F6E5A quattrostart https://www.youtube.com/watch?v=otCqqyV0f_Q Audi 90 20v turbo quattro vs nissan skyline 750hp https://www.youtube.com/watch?v=ubhOh2jTHFQ...

hi all
desired map AFR E85!
thank you

hi
can't connect the device to the computer,no connection!!

the other ecumaster unit connects without problems
I can send you the test??where it is possible to fix it??

samvel wrote:It does not matter if you set start or end of injection.
Cam profile is not going to help, you have to tune it for best efficiency.
But as i said before, in my opinion and experience, it is not very important with port injection in most cases.

Thank you!

RHD wrote:post up log file... looks like your getting camsync signal error

no errors on sync!

characteristics of the camshaft
The strategy of injection timing:
End of injection ???
Start of injection ???
at the beginning or the end??

it turns out?

how do I configure the injection angle?that's right, I built the table?
audi 90 motor 3b 2.2 875cc gt3584

the engine runs smooth!
https://drive.google.com/open?id=0Bwy8P ... HhmZDd4Nk0

Hey guys, can u check my KnockSensor settings. KnockSensors are the OEM from the 1.8T. The engine knock characteristic frequency used to configure the band-pass filter. This characteristic is different for every engine. It can be approximated with the following equation: Knock frequency (kHz) = 180...

There is no normal level of knock. The level depends on how you setup your knock sensor. The more gain you will set the higher is the resulting level. So you have to setup your sensor that it measures the engine noise in a good way and setup the knock threashold while running engine without knock. ...

is this normal?
https://drive.google.com/file/d/0Bwy8PV ... sp=sharing

Kisielisodd wrote:Firmware version, 1.100 in Your EMU

autotune features add in 1.134


UPGRADE EMU FIRMWARE to the latest version

thank you!
turned out, it worked

Open configuration -> log - Autotune window. In the Autotune window, press "ask" mark (help) and there will be manual, how to use autotune. Other issue, if there is problem with engine start after firmware upgrade, try this : - Save emu config map do hard drive - upgrade firmware - after upgrade op...

Kisielisodd wrote:Did you download and upgrade firmware in EMU ?

Download latest version of the software http://www.ecumaster.com/tv

downloaded Client for Windows 1.168 1 EXP. no car runs!
once connected to the ecu stops working!
how to turn on autotune??

autotune how to enable?
do not want to work.
thank you
help please to include

Karel wrote:On 5 cilinder you must know the TDC on working cycle for the 1st cilinder if you will use individual coils. (It wil be used as secondary trigger so CAM 1)

1k5 ?

pulldown always means connecting between sensor signal and sensor ground to lower the voltage, and noise also.

thank you

Karel wrote:On 5 cilinder you must know the TDC on working cycle for the 1st cilinder if you will use individual coils. (It wil be used as secondary trigger so CAM 1)

1k5 ?

pulldown always means connecting between sensor signal and sensor ground to lower the voltage, and noise also.

thank you