Ecumaster forum

Our another Corsa c20xe on EMU

Ok,thank you Karel

Hello
I would like to ask, if it is possible to use the EDL-1 Data Logger also on the (normal) EMU
Thank you and best regards

Yes of course

Update for 2016
and video:
https://www.facebook.com/adi.kronabitte ... 86?fref=nf

Hello
Yes the Crankshaft sensor is VR,but the Camshaft sensor, if Motronic 2.8 is Hall and need 12v+
Wiring Crankshaft sensor VR: Pin 1=B7,Pin 2=B18,Pin 3 Shield=B17
Wiring Camshaft sensor M2.8 Hall: Pin 1=12v+across the fuse,Pin 2=B15,Pin 3 Shield=B17

And a video
https://www.facebook.com/adi.kronabitte ... nref=story
https://www.facebook.com/DragOffTeamBer ... nref=story

Our Corsa on EMU,2.0 16v NA, 263hp-240NM-on 9000rpm

the coil pack new ??? we use the ecotec coil pack and that does the same thing when its getting old and we run 3 bar of boost on one of these coil packs up to 8200 but the sensors are known for it after 6.5k hall sensors are better over vr ones but if its a new sensor and its wired correct then it ...

Botasjr wrote:now i see one thing that i maybe need to test, i dont know,

i have rising edge on the primary trigguer
could this affect the engine?

Hello
Which crank sensor is in use, had the same problem with the Bosch sensor, I replaced it with Hella Sensor, operates at 9000 rpm with no problems

nyl wrote:Thanks for the info, i'm using 06e-905-115-e

Is the same ,also for the 07K 905 715 ,A,B,C,D,E,F coil

Hello That is dwell for the red Audi ignition coil 06F 905 9115 A,B,C,D,F 8V => 3,3ms 10V=> 2,8ms 12V => 2,4ms 14V => 2,2ms 16V => 1,5ms and pins 1: Power supply terminal 15 (+6 to + 16V) 2: mass terminal 31 3: control signal 5V (2.8V turn-on; off threshold 2.3V) 4: mass for control signal - Coil en...

Ok, to pin 30 on relay put wire + from battery, to pin 86 goes + wire from ignition switch, from pin 87 goes wire over the 20 a fuse to the fuel pump and on the pin 85 comes signal (ground) from the emu,depending on which pin you have a wire (aux 1-6 )(G4=aux6,G5=aux3,G12=aux5,G13=aux2,G21=aux1)whic...

For more Pumps,or fans

...It works

exactly

Hello! My motor has a 3-pole sensor I have already switched to trigger 60/9 Perhaps you know the injector phase? Hello Yes, both sensors are 3-pole, for hall sensor you need 5 or 12v, for the vr sensor only ground, if the sensor is original from the z20let engine, then it is vr (magnetic) and uses ...

here I still have the connection diagram and scope Hello peter Wenn ich mich nicht irre,hat der z20let motor vr kw sensor und nicht wie in deinen Primary trigger einstellungen zu sehen hall/optical sensor ,und der first trigger tooth sollte nr 9 sein,trigger angle dann 60 grad(prüfen mit lampe),bei...

hi HVR Team: where did you get that dwell time from which is written in the pdf? Hello On this side of Ray Hall is so written, using these dwell on n / a engine for two years without problems, and the engine running on 9000 rpm This wiring and the dwell is only for this coil(036 905 715f), the othe...