Ecumaster forum

hi im planing to install an ecumaster into a Jimmy 1.3 with engine G13BB year 2000 Does someone knows if ecumaster supports the original trigger from this engine? or i need to install a 36-2 trigger on the crank? im planing to build a pnp adapter at this moment im not sure, but i think the trigger p...

i cant make logs
and this happens

im having a strange problem with a black unit, in most of the time, the ecu dont power up properly, when i turn on the key, and the fan start to work, the engine dont start. in this case, the values of the temperatures on software came with -- value and nothing more happen. when i turn on the key, a...

closed loop will be probably in pro version.. ignition retard is design to slow down application of the torque to avoid "ringing" of dogs.. there is no other way to determine correct settings but testing in real conditions not on dyno .. what could be a good retard value, for a 220 bhp engine and 9...

hi there lets talk about gear cut into an atmosferic engine, no turbo... the system is activated by a switch, in this case a sadev gearbox with the original sadev switch on the gear box, then there is the point nº2, the cut delay, to compensate the mecanycal movement of parts, gear level, etc, then ...

hi
does someone have done an engine like that with an EMU?
it is possible to share the trigger patern and vanos information?
does it use vr or hall sensors?

soon im going to start a project like that, and i apreciate all information to start working

regards

For me, the pinout for this dbw is

0280750085

1 - M-
2 - M+
3 - Sng
4 - Potinv
5 - 5V
6 - Pot

Pedal

1 - Pot
2 - sng
3 - Potinv
4 - 5v

its not he same pinout from the ecumaster help

Problem solved

4K7 Pull up resistor from 5v to pot and potinv


https://www.youtube.com/watch?v=UyKskqsu04g

hi im doing some bench tests with a citroen C2 DBW setup im using the original 0280750085 body and im trying to use the original pedal sensor too, reference 0280752251, but without success. the pedal sensor have 4 pins 1 - pos 2 - sngd 3 - pos inv 4 - 5v i removed this information from autodata, and...

hi im doing some bench tests with a citroen C2 DBW setup im using the original 0280750085 body and im trying to use the original pedal sensor too, reference 0280752251, but without success. the pedal sensor have 4 pins 1 - pos 2 - sngd 3 - pos inv 4 - 5v i removed this information from autodata, and...

hi im starting to install an EMU into a S50B30 engine my plans is to build a plug and play conector into the original conector of this car, just remove the original bosch motronic, and plug in the ecumaster. this engine uses, the motronic to control fuel and ignition, and another ecu to control the ...

Maybe its the same as SR20? Try this one ok cool by the way, i changed the sensor from a bosch sensor, because the original is damaged, but no problem your information is always a good information. i have the engine runing, and almost tuned on the dyno, is working fine, till 1 bar of boost, after t...

hi

with the engine at 20 ºC the sensor shows -15 ºC

does someone have any calibration values for this sensor?

for the IAT im going to use an bosch sensor on the intake manifold.

best regards

hi

it is possible to install an EMU into a 300Zx?

Support software
Trigger
etc?

regards

There is a video of the final result

everithing works fine
for now
320 Hp at 0.8 Bar

https://www.youtube.com/watch?v=Ldv5DPZHy0I

job done

thanks to ecumaster info

my punout its a little diferent

NE - primary
G2 - Camsync
D8 - yes D8 - sensor ground.

hi after some information colected on this topic http://forum.ecumaster.com/viewtopic.php?f=19&t=10906&p=20522&hilit=3sge#p20522 i made my onw plug and play adapter, for now everithing seams to be fine, tps, clt, iat, etc, but, on the trigger its a little diferent compared with other base map from a...

There is no direct plug and play. The ECus differ sometimes by a few cable positions sometimes, by more. Best approach is to open the ECU and provide the pinout(its written on the board) to someone like ATS.Keep in mind you won't get too much from a 3sge even with EMU. Either swap a 3sgte inside, o...

It is, BLACK is basicly the same as the Standart EMU, just you dont need to add DBW module, or CAN module..... so the Mazda i made was the RX8 with turbo engine from RX7 (13B). So we needed Can for dash, ABS etc.. .and DBW for the RX8 pedal and Throttle body we used. If you dont need DBW and Can fo...

Karel wrote:As far as i know ....... i made already the first Mazda RX with Wankel on EMU BLACK

ok

but with the regular Emu is impossible, correct?