Ecumaster forum

Are there any kinds of Information/data sheet about the used serial protocol on the EMU, i would like to use this to get some information on my arduino.

What is about a PID-Controller for an electric water pump. E.g. CWA100/200/400 from BMW N-Engines?

Is it possible to expand the EMU Black Firmware for using of the both H-Bridges for two throttle bodies? I would like to use original BMW M70 throttle bodies on my V12 without the original BMW EML ECU.

Thx

ENCLOSURE IGNITION OUTPUTS Ignition output circuit was redesigned especially the driver of active coils. EMU BLACK supports active and passive coils (software selectable). In comparison to regular EMU it is possible to drive 2 active coils from one ignition output. In addition to this when active c...

Hello, i do not understand: What are the main benefits of EMU Black in Relation to the standard EMU? More inputs and outputs? Or something else?

Nice! Did you stay with oem ignition system ? Yes... if i would use 12 Ignition coils, so it would look a little bit disgusting I don't think so. https://www.youtube.com/watch?v=3DlMAiXh3mk Which Kind of ignition coils is used on this Vehicle? I can´t see these?... Ok, they are m50 Coils, but which...

Pan. B wrote:Nice!
Did you stay with oem ignition system ?

Yes... if i would use 12 Ignition coils, so it would look a little bit disgusting

An E36 with M73 V12 Engine and E60 530D manual GearBox. Power unknown

Emu does work very well

Jadzwin wrote:If I good rememember it works as an indicator of first cylinder.

Yes, that ie right!

Jadzwin wrote:But use is a little tricky, you need to enable engine start without sync

Is that possible with last EMU-Firmware, i think no, because i didn´t find this option at ignition settings?...

Hello @all,

does EMU support this kind of BWM Camshaft-Sensor, used on M20,M30 an M70 Engines:



It is mounted on the ignition cable of the Cylinder 6, Figure Nr. 9 at the Picture above

Hello dear EMU-Team, i wish some feautures, so i do not know how many work is neccesary to implement these, but here is my wish list: I have a V12 from BMW, so i would like to use one EMU control unit for each bank, but i want to use only one of: - crankshaft sensor - camshaft sensor - IAT sensor - ...

OK, ich have some understanding probs with wiring of Camshaft and Crankshaft Sensors: the shield-wire from sensor should be connected to both EMUs, how do i connect the plus-wire and minus-wire of the Crankshaft sensor to both EMUs? See the pic below: https://e5oarg-bn1306.files.1drv.com/y3m5Wto2nNA...

Because i do not like wasted Spark an wasted Injection
Germanys TÜV wants a lamda Control for both banks. And i want a nice 2 x R6 engine, like all BMW Cars with a V12 (each Bank has an own ECU).

But if it is not possible, so i have to use to Crankshaft sensors and two camshaft sensors

Hi Guys, i´m just done with mechanical building of my E36 354i with 6-speed transmission from an E31 850CSi.: https://ecujig-bn1306.files.1drv.com/y3mVCJLd9DLUJroNhiB2qLgfRhNlpyO8ql8I8YRAZvF16uOEjo8g-fiRK-OTO1tU3Gp1-cIRp9Obj17xkNJtUkl0M9UFtZjARyoFstE7AF-nFsM5dmbXDb0t2vOkbTbXFRQMbpf0i812nX-NEb3h8fNhX...