Ecumaster forum

Yes, it is running all right! Not everyday, as I have so many other "toys". See more ( even some videos), and thumb up if you like it: http://facebook.com/turbomatiz While looking at the weather forecast, it is soon time to put studded tires again :( Maybe some day I will try it on the dyno without ...

In revision C
- there are flyback diodes on AUX1 and AUX2
- there is no AUX4 pullup to 12V
- there is no CAN BUS terminator
- pin B38 is not sensor ground, do not connect.

I understand. However still it is not possible to add second DBW due to the lack of resources. For V12 it would be good idea to use 2 blacks :) Ray Hall is going to do it this way. Kuba Okay, understood. Tuning two ECUs in one engine would be fun! One bank (and ECU) at first, while leaving the othe...

The BMW ITB throttle cannot be controled using EMU BLACK H-Bridge at all. The current requirements are at least twice hiigher than peak current of black H-Bridges (they are capable to provide up to 7Amps each). Is it possible to expand the EMU Black Firmware for using of the both H-Bridges for two ...

Karel wrote:... on the Vanos side (intake) are two cam sensor. I think one will be "stable" and one will "trace" the movements..... ?

The front one is with one stationary tooth, and the intake side sensor is the one I used for the variable position.

Yes, when everything else fails, it is time to read the manual

(AUX outputs switch to ground.)

Artur,
Could you please check the FIT software link is really for version 1.44, as after I installed it, I still see version number 1.42. (And the hicups.)

We have had pretty cold all this week (last night -25 Celsius and day time maximum at -20 Celsius) but still I got my little Matiz alive and running after standing outside all week. And this was with E85 fuel, which is extremely difficult to ignite when cold. I did not use any engine heater, but nei...

Jakub,
Are you sure the link is to the new software? After installing it, it still shows 1.42 in the software. Also the random hickups at idle are the same as earlier.
Or, am I doing something incorrectly

One funny coincidence: Original Matiz ECU has similar 90 pin FCI connector than the new EMU PRO will have.
So, it will be a plug-in solution...

This is Daewoo Matiz 1.0 turbo with DET3 in FIT mode. (Sorry about the front bumber not yet fitted in the photo): http://jannenr1.kuvat.fi/kuvat/Projektit/Turbo+Matiz/WP_20150412_16_18_43_Pro.jpg/_small.jpg I had some spare time at our dyno on the Christmas Day and here are some graphs before and af...

clamp wrote: and why in this table i have MAP 290kpa? i use build in map ?!

You can change the map axles as you like and need. For instance, try clicking the 290kPa and change it to a value that suits you best.

Artur, Page 46

roquete wrote:hi, seems there is a bug in new version 1.123 Exp1, when i open one tab like sensors setup it opens the next tab down like engine start.
is it appening to me only? downgrade to 1.120 and all is ok.

Seems this came with v1.123, as v1.122 is ok.

I used to see similar happening, but it was only with older SW/FW.
What Software/Firmware are you using?

Moi Hemppa! Nämä kysymyksesi ja monet muut vastaavat saavat vastauksen Sporttiauton EMU-kurssilla selvällä suomen kielellä. Katso lisää seuraavasta linkistä: http://sporttiauto.com/index.php?p=ecumaster-ecu-kurssi (The same in English: These questions - among many others - are answered at Sporttiaut...