Hello I just wanted to know exactly hour to setup my vss & traction control? My setup is 2jzgte with a cd009 in 350z.
Basically I know where the vss wire is, do I need to tap that then pin into my emu? Does the traction control need a wire tapped into all 4abs sensors?
VSS & traction control setup?
Re: VSS & traction control setup?
The EMU only has one VSS input, so it needs to see the signal from the transmission.nolagg wrote:Hello I just wanted to know exactly hour to setup my vss & traction control? My setup is 2jzgte with a cd009 in 350z.
Basically I know where the vss wire is, do I need to tap that then pin into my emu? Does the traction control need a wire tapped into all 4abs sensors?
Re: VSS & traction control setup?
WHPZach wrote:The EMU only has one VSS input, so it needs to see the signal from the transmission.nolagg wrote:Hello I just wanted to know exactly hour to setup my vss & traction control? My setup is 2jzgte with a cd009 in 350z.
Basically I know where the vss wire is, do I need to tap that then pin into my emu? Does the traction control
need a wire tapped into all 4abs sensors?
Still doesn't assetrt my question,I want to know exactly what I have to do in order to get ire with my setup.
Re: VSS & traction control setup?
The signal wire from the VSS needs to go to the VSS input channel on the EMU.nolagg wrote:WHPZach wrote:The EMU only has one VSS input, so it needs to see the signal from the transmission.nolagg wrote:Hello I just wanted to know exactly hour to setup my vss & traction control? My setup is 2jzgte with a cd009 in 350z.
Basically I know where the vss wire is, do I need to tap that then pin into my emu? Does the traction control
need a wire tapped into all 4abs sensors?
Still doesn't assetrt my question,I want to know exactly what I have to do in order to get ire with my setup.
Re: VSS & traction control setup?
Basically I know where the vss wire is, do I need to tap that then pin into my emu? Does the traction control
Ok well since it is a can bus does that matter?I know in the 350z, the vss signal wire tune up to the can bus type box in my climate control.would I just tap off of that? Or do you know that the cd009 350z trans has a specific sensor?
need a wire tapped into all 4abs sensors?[/quote]
The EMU only has one VSS input, so it needs to see the signal from the transmission.[/quote]
Still doesn't assetrt my question,I want to know exactly what I have to do in order to get ire with my setup.[/quote]
The signal wire from the VSS needs to go to the VSS input channel on the EMU.[/quote]
Ok well since it is a can bus does that matter?I know in the 350z, the vss signal wire tune up to the can bus type box in my climate control.would I just tap off of that? Or do you know that the cd009 350z trans has a specific sensor?
need a wire tapped into all 4abs sensors?[/quote]
The EMU only has one VSS input, so it needs to see the signal from the transmission.[/quote]
Still doesn't assetrt my question,I want to know exactly what I have to do in order to get ire with my setup.[/quote]
The signal wire from the VSS needs to go to the VSS input channel on the EMU.[/quote]
Re: VSS & traction control setup?
Yes connect the wire from the Transmision im the VSS from the Emu
But you Must select in the Option "calculated"
But you Must select in the Option "calculated"
Re: VSS & traction control setup?
The wires run into the can bus system though I believe i the cabin.there's 2vss wires one with a4 puller the other with an8.
Re: VSS & traction control setup?
Does it matter
Re: VSS & traction control setup?
It shouldn't matter.