Bugs and Feature reqests

[WHPZach]

Hi!

I've checked your settings and boost output. Everything works as expected. I suppose that you have problem with the DC Error correction table that change your DC.

Hello Jakub, again a problem with my wastegate actuator, the wiring sheme is like in the picture attached. The signal should be a PWM signal @300 Hz with duty cycle between 3 and 93%.
I measured with the oscilloscope a very nice and clean square wave with a very exact frequency at the signal wire, but the duty cycle only shifts between 2 to ~75% even though I set the min/max values to 2/98% in emu client.
the strange thing is, Emu somehow makes a additive error to the dc.
E.g. 29% in emu client makes a real DC of 2% and 100% in client makes 75% in reallity. So when I further reduce the DC in client(from 29 % downwards) real DC stays at 2%. that happens vice-versa when inverted the output.

Is my wiring correct?

what could be causing that problem?

thanks in advance!

Is 300 Hz a typo?

[clem]

AAAA thanks very much!!!

[clem]

As I work thru my often very long logs, it would be nice to have an option for highlighting or marking the cells which have been modified (e.g. values written in different colour?) , for having a better overview where you have already been!
Maybe with a reset button or a reset after a new project has been loaded, Is that possible?

Kind regards Clem

[roquete]

hi, seems there is a bug in new version 1.123 Exp1, when i open one tab like sensors setup it opens the next tab down like engine start.
is it appening to me only? downgrade to 1.120 and all is ok.

[Jean Niemi]

hi, seems there is a bug in new version 1.123 Exp1, when i open one tab like sensors setup it opens the next tab down like engine start.
is it appening to me only? downgrade to 1.120 and all is ok.

Seems this came with v1.123, as v1.122 is ok.

[Jadzwin]

You right. Tommorow will be fix for this issue.

[Jadzwin]

Version 1.123 exp2 already on the server.

[aslot]

Version 1.123 exp2 already on the server.

I cant find 1.123exp2 on the server?

[nemitom]

v. 1.125 not work gauge skin... is only white. My problem only?

[Ace-Motorsports]

V1.125 is not working correctly, if I try to open boost parameters it opens output fuel pump, boost target opens param. output 4. etc. Also all gauge names are not readable, instead of the gauge name you see the buttons for minimize maximize and fullscreen. OS is windows 8.

[Jadzwin]

Enable all available strategies then it will work.
Tommorow will be fix for it.

[Jadzwin]

Hi Jakub
RE time based boost control
I did some testing this weekend with closed loop boost control, i now have boost accurate to +- 5KPA of target table.
at this level of control i will need to change the boost target / time step in 0.5 second increments at the start of the run will this be possible ?

There is new version on the server 1.126
There is new functionality called Timers. The timers could be triggered by Virtual outputs.
For example you can trigger timer1 by Virtual output condition VSS > 1km/h
Then you can alter your boost or / and ignition angle in function of this timer.
I think it helps you.

Other usage is for full throttle drive to retard ignition and enrich the mixture if you drive long. It is good for track or highways to prevent engine against failure.

[nemitom]

Please look at my problem .... http://youtu.be/cKbIVLjKdmI
application does not work correctly
thanks

[Jadzwin]

It is 1.126 ????
Was the gauges displayed correctly in previous versions ?

[nemitom]

yes is 1.126
in previous version 1.125 BAD and in version 1.124 and down is ok....

[Jadzwin]

What is your configuration for available strategies ?

[nemitom]

I have a off two strategies. If I turn on all the strategies, the menu tree is ok.
But the gauges it is wrong. I try re-install the graphics drivers.

[roquete]

would be nice to have a simpler "end user" version of the client software (like a diagnostic only software) with only logging and error code capabilities, this way far away costumer does not mess with mappings and setups.

[WHPZach]

would be nice to have a simpler "end user" version of the client software (like a diagnostic only software) with only logging and error code capabilities, this way far away costumer does not mess with mappings and setups.

Password protection is a good solution for that problem.

[roquete]

would be nice to have a simpler "end user" version of the client software (like a diagnostic only software) with only logging and error code capabilities, this way far away costumer does not mess with mappings and setups.

Password protection is a good solution for that problem.

yes but if diagnostic is needed at distance software gets too complicated for the end user even if it can log without password the tables still appear and all available strategies.
what i mean is something like the android bt version but for windows.